1/8 scanning 32x16dot 1R1G1B 10000pixel/sqm P10 SMD LED display
Specifications :
| outdoor DIP P10 |
| Resolution/mm | 10 |
| Pixel configuration | 1R1G1B |
| Pixel density/pixels/m² | 10000/m² |
| Module resolution | 32x16 |
| Module size/mm | 160X160MM |
| View distance | 14-300m |
| Single point brightness adjust | Can be added |
| Single point color adjust | Can be added |
| White balance brightness | >7500cd/㎡ |
| Color temperature | 6500K-9500K |
| Horizontal view angle | 120(degrees) |
| Vertical view angle | 60(degrees) |
| Signal Process bit | 10 or 16bit |
| Grey process | 1024x1024x1024 16834x16834x16834 65536x65536x65536 |
| Control distances | Internet cable:100m, multimembrane:500m, monofilm:2km |
| Driving mode | Constant driving current |
| Scanning mode | 1/4 SCANNING |
| Frame rate | 60Hz |
| Refresh frequency | >3000Hz |
| Control mode | Computer synchronous |
| Brightness adjusted range | Manual, automatic operation, stepless continuous adjusted |
| 255 steps. No grey loss |
| Out of control point | <1/10000 |
| Working hours | ≥72hours |
| Mean Time Between Failure | >5000hours |
| Life time | 100000hours |
| Life-all-white(brightness halving) | 50000hours |
| Environment temperature range | Operating temperature range: -20-45℃ |
| Self-check technology | LED spot self-check, communications check, power check, |
| temperature monitor(need customization) |
| Remote monitoring | Remote supervision and control, record potential fault, |
| send out warning signs to the operators.(need customization) |
| Software environment | WindowsNT,Windows1999,WindowsXP |
| Luminous point width between centres | Deviation<3% |
| Brightness uniformity | <10% |
| Color uniformity(chromaticity coordinate) | ±0.003 |
| Power supply request | AC85-264V(50Hz-60Hz) |
| Contrast | (1000:1) |
| System protection | Moistureproof,dustproof,high temperature
protection,anti-corrosion,anti-burning,anti-static,anti-vibration |
| Humidity(working) | working:10-95% |
| Humidity(storing) | storing:10-95% |
Compared with DIP products, the advantages of SMD products are as
below:
1. Better color mixing effect: SMD requires higher soldering
technology and more mass production processes than DIP, and 3 chips
are packaged in a small cup, which makes the pixel spacing between
the 3 chips smaller. Therefore, SMD has a higher color ratio than
DIP LED, better color mixing effect, and closer viewing distance.2.
Due to the small chip size of SMD lamps, the energy required for
operation is lower, which will save about 30% compared with DIP LED
displays.3. The chip size is smaller, taking up less space, and
special installation technology enables us to produce higher
density displays. Our recently launched P4 SMD indoor LED display
has proved this.4. SMD lamps have less materials and no longer feet
than DIP LEDs, which will make the screen lighter.5. Wider luminous
angle: DIP lamps mainly use "U" type lamp cups, and the chip
position is always at the bottom of the "U", so since SMD will
encapsulate the chip on the surface of the lamp cup, its luminous
angle is smaller than that of SMD lamps.
Shipping Detail:
UPS/Fedex/TNT/DHL, By air, By sea
Q1,How to arrange payment?
Our payment terms in usually is T/T payment,for sample and small
order,Western union,Paypal or Moneygram also be acceptable
Q2,What is our warranty?
Our warranty from 5year to 1year basis on different type led
screen,In usually every screen we will ready more extra led screen
moduless as spare modules,if some modules happen fails,you can
replace the fail modules by our spare modules,When all the spare
modules use out,You can send back these modules to us for
repair,and we will send to you after repair and testing&aging
well
Q3,How to be our distributor?
To be our distributor,We can share our profit together with you in
every year,Also we can send our engieer or sales to your compay to
support your business,also for led screen after-service,We will
together with you to the after-service in the whole led screen life
time
Q4, How to maintence led screen?
In usually every year to maintence led screen one time,clear the
led mask,checking the cables connection,if any led screen modules
fail,you can replace it with our spare modules
FAQ
Q1: How to help client choose suitable display?
A1:
(1)specific application scenario
(2)viewing distance requirement
(3)display brightness requirement
(4)specific installation environment
(5)budget and cost control
Q2: What about your technical support?
A2: Proffessional engineers are on standby, can offer guidance, on
site technical support as required.
Q3: What's the control system?
A3: For synchronization control: Nova, Linsn or Mooncell control
system.
For asynchronous control: Onbon or Xixun control system.
Q4: What's the warranty of your LED displays?
A4: We provide 2 years warranty and conditioned lifetime technical
support for our LED display products.
Q5: What's your payment method?
A5: Our payment method is T/T 30% as deposit, balancing before
delivery.
